Ge belt replacement

Ge belt replacement DEFAULT

How to Change a GE Dryer Belt

  • Unplug the dryer and open the dryer door.

  • Unscrew the screws under the top lip, where the dryer's door closes, with your screwdriver. Once these screws are removed, lift the top off of the dryer. On older models, the entire top will hinge upward out of the way, and on models made after 1997, half the top will pull off.

  • Remove the screws on the inside-top corners of the front panel so the front panel of the dryer can be removed and set aside. On models made before 1997, the front panel should be carefully set to the right side; on newer models, the panel should be set to the left side of the machine. Be careful not to damage the door-control wires.

  • Locate two screws approximately 6 inches off the floor on each side and remove them, allowing you to push the sides of the dryer slightly apart so the drum can be removed. Pull the drum slightly toward you and reach around to remove the dryer belt from the motor pulley. If the belt is broken, this step should not be necessary. Once the belt has been removed from the motor pulley, the drum should pull up slightly and out of the dryer toward you.

  • Remove the old dryer belt and put the new one in place, with the ribs of the belt facing the drum. The slack part of the belt should be placed near the motor. Reverse the previous directions to replace the drum, replace the screws that hold the sides in place, replace the front and replace the top.

  • Pull the dryer out from the wall and remove the four screws holding in the panel near the bottom of the back of the dryer. You will see the motor, the drum and the belt you just set in place. Loop the belt around the motor pulley and the idler pulley, and turn the drum by hand to make sure that the belt is straight and will stay in place. Screw the panel back on and push the dryer back into place against the wall.

  • Tip

    Older dryers will have a dark drum; newer dryers will have a light-colored drum.

    Sours: https://homesteady.com/13642393/how-to-change-a-ge-dryer-belt

    How to Replace GE Dryer Idler Pulley and Belt

    If you have a squeaking dryer it may be that idler pulley is worn out.  One sign that it is the idler pulley is if the squeak is made at a high frequency (because the pulley goes around many times for each drum revolution).  My GE Dryer Model DCVH515EF0WW was louder than I felt it should be.  I replaced the front drum glides but it was still loud.  You can read how to install the front drum glides here:

    How to Fix Squeaking GE DCVH515EF0WW Dryer-Replace Drum Glides

    I decided to replace the rear bearing and you can read that article here:

    How to Replace Rear Bearing on GE Dryer

    While I was replacing the rear bearing I figured I’d go ahead and replace the idler pulley and belt.  Follow along to replace yours…

    Equipment:

    Parts Needed:

    Tools Needed:

    How to determine your GE Dryer model: Open the door and look at the bottom right edge of the dryer’s opening:

    dryer identification label
    Dryer Model Identification Label

    Step 1: Unplug your dryer.

    If it is an electric dryer like mine you are dealing with 220V.  Regardless, make sure to unplug it before working it on so you don’t get electrocuted.

    Unplug Dryer Before Working On It

    Step 2: Remove the 3 Phillips screws on the top edge of the back of the front bezel.

    Dryer Top Back Molding Screw Location

    Once you have removed those three screws you can put your fingernails in the seam and slide the bezel toward the back of the dryer.

    Top Back Molding Removed

    Set the bezel and the three screws aside.

    Step 3: Remove the top two cover screws.

    They are Phillips head screws:

    Top Panel Screw Locations

    Step 4: Remove the top panel.

    Lift up the front edge of the top panel and slide the panel toward the front and remove the top panel.

    Lift the front edge and slide the panel toward the front

    Step 5: Disconnect the light, switch, and control panel wiring connectors.

    Before you proceed you need to disconnect three wiring connectors.  One is a parallel computer-type ribbon cable for the controls, one is for the light, and the other is for the door light switch (the latter two have tabs you must lift in order to disconnect them):

    Dryer Wiring Connector Locations

    I put one finger on the left side under the ribbon cable and the other on the right side of the black connector, wiggling the connector and pulling up to remove it.  Be careful because you can actually pull this ribbon connector apart.  I’ve taken my dryer apart about 4 times now and one of the clips on the end that holds the black connector together has begun to come apart.  Be gentle and wiggle the connector around as you pull up.

    Ribbon Wiring Connector Removal

    The other two connectors are a similar style where you must lift up the “catch” and pull them apart as shown below:

    Lift the tab to remove the connector
    Wiring Connector Disconnected

    Step 6: Remove the control panel.

    Remove the two top control panel mounting screws:

    Bezel Mounting Screw Locations

    Then lift the control panel up and off:

    Lifting Control Panel Off

    Set the control panel aside in a safe location.

    Step 7: Loosen the lower front panel screws.

    I found it easier to get at them by propping the front edge of the dryer up on my screwdriver case as you can see below.  Loosen, but do not remove, the lower front panel screws.  If you don’t loosen them enough, almost a quarter-inch, you will not be able to lift the panel up and off of them (I ran into that issue).

    Lower Front Panel Screw Locations

    Step 8: Remove the upper front panel screws.

    Remove the two Phillips screws from the upper front panel:

    Upper Front Panel Screw Locations

    Once you have removed the upper front panel screws you will want to hold the front panel on to the dryer and swing shut the dryer door.

    Step 9: Lift the front panel up and off the dryer.

    Lift the front panel up and off the two lower screws that you loosened in Step 7.  Be careful because the door will want to swing open (which makes the front panel want to fall forward then).

    Front Panel Removed

    Here’s another view:

    Front panel removed

    Step 10: Turn the front panel around and inspect the four drum glides.

    While you are in here you should take a look at the drum glides.  The drum guides are shown by the arrows in the picture below:

    Drum Glide Locations

    This is what good OEM drum glides should look like, the top two should be of a darker material:

    This is what OEM drum glides look like

    Mine where NOT OEM and they were all worn out:

    Left Drum Glide Locations

    These two were completely worn out.  As you can see from the picture below, the top glide and the bottom glide are both white.  The top one, if it is a factory replacement, should be a dark-colored material.   I had purchased third-party glides off of amazon and they turned out to be worthless and wore out in less than a month because they were made of a softer material.  They were also loud too.  Anyway, if you have the dryer torn apart you ought to replace these while you are in there if they are worn out:

    Right Drum Glide Locations Up Close

    If your drum glides are worn through make sure to replace them.  I have the part numbers and all the steps to replace them (it’s easy) on my article here:

    How to Fix Squeaking GE DCVH515EF0WW Dryer-Replace Drum Glides

    Step 11: Remove the belt from the idler pulley and motor shaft.

    We need to remove the dryer drum so we can get at the bearing that is attached to the back of the drum so we need to disconnect the belt from the idler pulley so the drum will be freed from the dryer.  You can see the idler pulley via the lower left corner, just above the blower fan:

    Location to access the belt and tensioner pulley

    If you shine a flashlight back in there and look into that triangular-shaped access hold this is what you will see:

    The location of the drive belt, tensioner pulley, and belt path

    To remove the belt from the pulley push the pulley down to take tension off the belt and work the belt off as shown below:

    GE DCVH515EF0WW Dryer Removing Belt From Tensioner

    Move the belt to the right side of the pulley and make sure it is not on the shaft of the motor:

    Move the belt to the right side of the pulley

    Also make sure the belt is not looped under the motor shaft which is out of sight in the picture below.

    Step 12: Remove the drum.

    Use the belt to lift the back-end of the dryer and grab the front lip with your fingers and slide the drum straight out towards the front.  If you didn’t unhook the belt from the idler pulley AND motor shaft you will run into issues at this point.  Here you can see me supporting the back-end of the drum:

    Lift the back end of the drum with the belt
    Pry the metal sides apart as necessary

    Here’s the drum removed:

    Drum removed

    Here is the dryer with the drum removed:

    Dryer with the drum removed

    Step 13: Vacuum out your dryer.

    While you have your vacuum torn apart you ought to vacuum out the inside of the dryer.  There was some lint that had built up around the edges of our dryer:

    Vacuum out Your Dryer

    Step 14: Remove the old idler pulley.

    The nut on the end of the idler pulley takes a 7/16″ socket to remove it:

    Use a 7/16" socket to remove the nut

    The idler pulley will slide straight off.  Here is the replacement (yell0w) with the original.  They were slightly different but the replacement fit perfectly on the shaft and that’s most of what matters:

    The original idler pulley (top) and replacement (bottom)

    Step 15: Grease the replacement pulley.

    I simply squirted the entire pulley full of grease:

    Grease the replacement pulley before reinstalling

    Step 16: Reinstall the idler pulley and nut.

    One thing I’d mention is that the nut will keep screwing on farther and farther (too far) so you need to watch how far you tighten it on.

    Slide on the greased pulley and reinstall the nut

    Step 17: Reinstall the belt on the drum.

    One thing I must note is that the new belt will be shorter since the old belt has stretched out:

    New and old drum belts

    Make sure the ribbed side faces the drum (the picture below is both belts side-by-side, ribbed side up):

    The ribbed side of the belts

    Slip the drum through the belt, ribbed side toward the drum, and align the belt on the groove closest to the back of the drum (you will be able to see wear on the drum to indicate the right place):

    New belt installed on drum

    Step 18: Reinstall the drum into the dryer.

    Supporting the back-end of the drum with the belt, slide the drum into the dryer body.  You will need to pry out the sides of the dryer to get the drum to fit between them.

    Reinstalling the drum into the dryer

    It takes some patience to align the drum up with the retainer bearing so the bearing fits in its place.  Be careful to not “stab” the dryer elements with the bearing as you could damage them.  You will know that you have inserted the bearing into the retainer when the top of the drum has the gap shown below (and use this picture to guide yourself when you are reinstalling the drum):

    The correct gap above the drum

    The front edge gap should look like this:

    The correct gap in front of the drum edge

    Step 19: Reinstall the belt on the motor and idler pulley.

    First make sure the belt is correctly aligned and oriented on the drum.  The belt should go in the groove that is closest to the back of the dryer and the ribbed side of the belt should face the drum as seen below:

    Belt Correctly installed on Drum

    Here’s how I set it up to access the belt and reinstall it on the motor and pulley:

    Location to access the belt and tensioner pulley

    The belt is going to feel like it is too short, but it will fit.  First put the belt on the motor shaft, second, bend the pulley down,  and third, slide the belt up and over the lip on the edge of the pulley:

    Steps for reinstalling the belt on the motor shaft and pulley

    Step 20: Test the belt installation.

    If the belt is installed correctly, when you turn the drum (while supporting the front edge of the drum), the blower will turn, since it is directly connected to the shaft on the motor:

    Blower fan location

    Step 21: Reinstall the front panel on the dryer.

    You will need to slip the two bottom “slots” on to the two screws you loosened in Step 7.

    Reinstalling Front Panel

    As you lean the top of the front panel towards the dryer you will need to move the wiring connectors out of the way so they don’t go into the drum and also you will need to lift the drum up so it slips on to the bearing assembly:

    Lift Drum Up to Slide onto Bearing

    You will also need to line up the curved tab on each edge of the front panel with the notch on the sides of the dryer.  I needed to squeeze the sides of the dryer in to line it up (both sides are the same):

    Line Up Curved Tab With Notch

    Here’s a picture of the front panel in place:

    Dryer Drum On Bearing

    Reinstall the upper front panel screws:

    Reinstall the upper front panel screws

    Tighten the two lower front panel screws:

    Tighten the two lower front panel screws

    Step 22: Reconnect the light and door light switch electrical connectors.

    These connectors only have one way they can go on and one has 3 wires and the other has 2 so you can’t get them mixed up:

    Reconnect the light and light switch connectors

    Step 23: Reinstall the control panel.

    The control panel has a slot on the bottom edge that sits down over the metal lip on the dryer body as illustrated below:

    Reinstalling Control Panel

    Here the control panel is set back on to the body (arrows indicate where the control panel fits over the edge of the metal frame):

    Control Panel Installed

    Reconnect the control panel ribbon cable.  The female side (on the dryer) has a notch that fits a piece that sticks out on the connector so it will only fit one way:

    Reconnecting Control Panel Ribbon Cable
    Reconnect the light and door switch connectors

    Reinstall the two screws into the left and right ends of the control panel:

    Reinstall the 2 Control Panel Screws

    Step 24: Reinstall the dryer top panel.

    There are two “catches” that hook into the underneath side of the top metal panel (circled below).  Set the back edge of the top panel on the top of the dryer and slide it back, centering it on the top of the dryer, and once it locks in place you can set down the top.

    Reinstalling the dryer top panel

    Then reinstall the two long top panel screws:

    Reinstall the two long top panel screws

    Step 25: Reinstall the back molding.

    Slide the back of the bezel in place and reinstall the three Phillips head screws:

    Reinstalling the back top molding

    Step 26: Cautionary Note

    If you have perchance pulled your dryer away from the wall you may want to verify that the dryer is still correctly connected to the exhaust pipe on the back.  It isn’t dangerous to have it disconnected but you will vent dryer lint all over your house if you blow the exhaust into your laundry room.

    Step 27: Plug it back in

    If your rear bearing was bad you should notice quite a difference having installed a new one.  Now you’ve fixed your dryer bearing issues and saved a lot of money.

    Other Links:

    Amazon Associate Disclosure: As an Amazon Associate I earn from qualifying purchases. This means if you click on an affiliate link and purchase the item, I will receive an affiliate commission. The price of the item is the same whether it is an affiliate link or not. Regardless, I only recommend products or services I believe will add value to Share Your Repair readers. By using the affiliate links, you are helping support Share Your Repair, and I genuinely appreciate your support.

    Related

    Sours: https://www.shareyourrepair.com/2015/12/how-to-replace-ge-dryer-idler-pulley-and-belt.html
    1. Manchester animal shelter
    2. Delicate synonym
    3. Excel numberformat
    4. Nissan erie pa

    How to Replace a Dryer Belt

    lift dryer lid and inspect belt

    replace existing belt if worn

    Lift the Lid, and Inspect the Belt

    Unplug the dryer. If the plug can be reached without moving the dryer, the dryer probably won't have to be moved.

    Use a putty knife to press the clips holding the lid in place (Image 1). Lift the lid.

    Look at the existing belt. If it looks worn (Image 2), it will need to be replaced.

    disconnect electrical connection for door switch

    remove screws holding front cover of dryer

    Remove the Front Cover

    Disconnect the electrical connection for the door switch from the front of the dryer (Image 1). Remove the screws holding the front cover of the dryer in place (Image 2). Lift up the front cover, and pull it off the dryer.

    Cut the Belt, and Remove the Drum

    Cut the dryer belt with scissors, and pull the drum straight out so the motor and pulley are easily accessible.

    Place the Belt Around the Drum

    The belt will be threaded around an idle pulley and looped over the drive shaft.

    The idle pulley helps keep the belt tight (Image 1).
    Place the new belt around the drum so that the rubber surface (Image 2) touches the drum. The rubber surface has ridges that help it keep good traction.

    Set the Drum Into the Dryer

    Set the drum back into place so that it rests on the rollers inside the dryer. Use a bungee cord to hold up the front of the drum.

    access the drive shaft from underneath drum

    Attach the Pulley, and Replace the Front of the Dryer

    Reach underneath the drum to access the drive shaft (Image 1).

    Set the idle pulley in position if necessary. The pulley snaps into two grooves in the cabinet body. Loop the belt under the idle pulley, and attach it to the drive shaft (Image 2)

    Replace the front of the dryer, and attach the top by reversing the removal procedure.

    Sours: https://www.diynetwork.com/how-to/rooms-and-spaces/basement/how-to-replace-a-dryer-belt
    Dryer Belt Replacement

    .

    Belt replacement ge

    .

    GE electric or gas dryer belt

    .

    You will also be interested:

    .



    352 353 354 355 356