Audio control lc

Audio control lc DEFAULT

AudioControl LC RMS 5-Channel Amplifier

AudioControl LC

Two keys to unlocking great sound in a car stereo system are serious power and extensive control — and this amp's got them both. For power, AudioControl's LC five-channel amplifier puts out watts RMS to four channels and up to watts RMS to a sub. If you're into mega-power, competition-type systems, you could bridge this amp to 3-channel mode and drive a couple of high-performance components with watts RMS each while powering a sub with watts RMS — that's watts in total.

This amp will work well with a 3-way system that uses a pair of tweeters, midrange speakers, and a subwoofer. Highly adjustable crossover networks let you set high-pass, low-pass, and bandpass filters so each driver gets only the frequencies it was designed to play. AudioControl's AccuBASS® circuit ensures maximum bass performance, even if you're connected to a factory radio that normally turns down the lower frequencies as you turn the volume up

AudioControl designed the LC to work equally well with aftermarket and factory stereos. Eight active speaker-level inputs allow you to connect to almost any factory radio, with signal summing accommodating the separate bass, midrange, and treble signals found in some factory systems. Signal sensing circuitry turns the amp on, via the front speaker-level inputs, so you won't need to run a remote turn-on wire throughout your vehicle.

Onboard LEDs indicate optimized signal flow for inputs and outputs, plus give you a warning when a source is too loud and causing distortion. An optional wired remote can get assigned to each and every channel pair so you can control volume from the front seat.

Important Note: Some factory radios and amplifiers will not work without sensing that its speakers are connected to their outputs. If you don't have output from your factory system after installing this amplifier, you'll need an AudioControl load-sensing adapter (sold separately) to correct the issue.

Product highlights:

  • 5-channel car amplifier
    • watts RMS x 4 + watts RMS x 1 at 4 ohms
    • watts RMS x 4 + watts RMS x 1 at 2 ohms
    • watts RMS x 2 bridged at 4 ohms + watts RMS x 1 at 2 ohms
  • Class D amp technology
  • MILC™ (Maximum Input Level Control) LED optimization and clip indicators
  • stereo/mono switch on channel pairs

Tuning Controls:

  • Ch 1/2:
    • variable high-pass filter ( Hz or Hz, 12 dB/octave)
    • front high input level control — when using amplified factory tweeter wiring
  • Ch 3/4:
    • variable high-pass or bandpass filter (HP: Hz; LP: Hz, 12 dB/octave)
  • Ch 5:
    • variable low-pass filter ( Hz, 12 dB/octave)
    • AccuBASS® circuitry for improved bass response

Other Features:

  • 6 preamp and 8 summable speaker-level inputs
  • GTO™ (Great Turn On) signal-sensing turn-on with Ch1/2 speaker-level input
  • optional wired remote level controller available
  • fuse rating: 40A x 3
  • wiring and hardware not included with amplifier
    • 1/0-gauge power and ground leads recommended
  • dimensions: 12"W x /8"H x /2"D
Sours: https://www.woofersetc.com/camplifiers/cmulti-channel/audiocontrol-lcrmschannel-amplifier.html

AudioControl LC 4/3/2 Channel High Power Amplifier with AccuBass

You want power? The key to building a great car stereo system is power with control. AudioControl's LC 4-channel amplifier generates watts RMS per channel, so it'll drive even the most demanding aftermarket speakers with plenty of headroom to spare. And it'll rumble the low end too - bridge this versatile amp's output and you've got watts per channel on tap to get your subs bumping. Control is key When it's time to dial in the sound, you've got plenty of control. Highly adjustable crossover networks let you set your high- and low-pass filters precisely, and AudioControl's celebrated AccuBASS circuit ensures maximum bass performance, whether you're connected to an aftermarket or factory stereo. The optional ACR-1 wired remote lets you control the volume from your front seat. Onboard LEDs indicate optimized signal flow for inputs and outputs, plus give you a warning when a source is too loud and causing distortion. Add kick to your factory stereo AudioControl designed the LC to work equally well with aftermarket and factory stereos. Six active speaker-level inputs allow you to connect to almost any factory radio, while signal summing accommodates the separate bass, midrange, and treble signals in some amplified factory systems. AudioControl's GTO(tm) Signal Sense circuitry turns the amp on automatically whenever it senses a signal coming from the speaker-level inputs. A suite of controls lets you dial in the sound output.

Sours: https://www.amazon.com/AudioControl-LCChannel-Amplifier-AccuBass/dp/B01EDIWFFC
  1. Simple origami shapes
  2. Chillicothe mo radar
  3. Tcb cleaning

Audio Control LC High-Power Multi-Channel Amplifier with Accubass®

Audio Control LC High-Power Multi-Channel Amplifier with Accubass®

The LC brings five channels of sonic purity and unprecedented levels of power to a complete range of multi-channel and subwoofer amplifiers from AudioControl. Featuring eight active speaker level inputs, six line level inputs, the LC is packed with intuitive setup controls for high-pass, band-pass, and low-pass filters, automatic and selectable signal summing, and AccuBASS. Integrate seamlessly with your OEM or aftermarket sound system with this single-amp solution, which will transform your audio with impressive power levels delivered to your speakers and subs. Add the optional ACR-1 remote for level control.

Features

Configurable as 5 or 3 channel amplifier
4 x watts + 1 x watts @ 2 ohms
4 x watts + 1 x watts @ 4 ohms
watts @ 4 ohms bridged
AccuBASS® Processing
MILCTM Maximum Input Level Control (Patent Pending)
GTOTM Signal Sense
3-way Independent Linkwitz-Riley Alignment crossovers
Summable active speaker-level inputs (8 channels) for OEM integration
6 preamp inputs
PFM Subsonic Filter
Optional ACR-1 assignable remote control
Solid One-Piece Aluminum Chassis

Specifications

Inputs

Preamp Inputs: 6 balanced
Preamp Input Voltage Range: mV – 6 Vrms
Speaker Level Inputs: 8
Speaker Level Input Voltage Range: 3 V – 40 Vrms

Outputs

Rated Continuous (RMS) Power at V:
4 Ω – W x 4 + W x 1
2 Ω – W x 4 + W x 1
Bridged 4 Ω – W

Performance

Frequency Response: 20 Hz – 22 kHz
Signal to Noise: dBa, Ref W @ 2 Ohm
THD+N: < %
Minimum Power / Ground Wire Gauge: 3 AWG wire
Fuse Rating: 4 x 30 A
Crossover: 3-way Linkwitz-Riley, Adjustable From 30 Hz – Hz

Weights & Dimensions

Dimensions: ″W x ″D x ″H
Weight: lbs. (kg)

Sours: https://www.cartoys.com/audio-control-lc
LC7i Active Line Out Converter Discussion and Review

Product Spotlight: AudioControl LC Amplifier

AudioControl LCLocated in Mountlake Terrace, WA, AudioControl has been building cool audio equipment for more than 40 years. At the Consumer Electronics show in Las Vegas, they launched a new member of their LC series of amplifiers, the LC The AudioControl LC is a high-power six-channel amplifier with some amazing and unique features that make it perfect for multi-channel OEM integration solutions.

About the AudioControl LC Amplifier

AudioControl LCAudioControl rates the LC as being able to produce a healthy watts per channel when loaded to 4 ohms and a downright beefy watts per channel when loaded to 2 ohms. Any pair of channels can be bridged to produce watts into a single 4 ohm load. Having this much power on tap not only means that your speakers will get good and loud before the amplifier distorts, but also that you can bridge any pair of channels to easily power a subwoofer.

The top of the amplifier has what may be the longest row of adjustments ever for an amp that size. Each pair of channels has a sensitivity control and crossover frequency control. Channels 1 and 2 include a high-pass crossover that is adjustable from 30 to Hz, or to 5, kHz, depending on the position of the adjacent range switch. On channels 3 and 4, you have the option of a high-pass or band-pass crossover, and on channels 5 and 6, you can select low- or high-pass filtering. This crossover flexibility allows for easy front, rear and subwoofer configurations, or a three-way setup with an active front stage and a subwoofer. Each pair of channels has a stereo/mono switch, and an option for output level control from the ACR-1 port. The ACR-1 remote control is optional.

AudioControl LCTied to the ACR-1 port is AudioControl’s AccuBASS feature. AccuBASS allows the installer to apply a low-frequency bass boost to compensate for the roll-off found in many factory source units. Unlike other boost circuits, the AccuBASS boost circuit starts working above an adjustable threshold to keep the system from sounding boomy at low volumes.

OEM Integration Features

AudioControl LCThe LC features whopping eight-speaker level input connections. The amp allows you to sum the signals from these inputs and deliver them to different pairs of channels, using a switch on each of the channel pairs. If your factory audio system has a two-way front stage, rear fill speakers and a sub, or a three-way front stage and a sub, this amp will take care of combining the signals back together without the need for external components or equipment.

The LC includes the AudioControl GTO circuit. GTO stands for Great Turn On. When GTO is set to the Off position, the amplifier turns on when 12 V is present at the remote turn-on lead. When GTO is turned on, the amplifier monitors its inputs for the presence of an audio signal or the DC voltage offset present in most source units and small factory amplifiers. GTO makes getting the system up and playing quick and easy.

System Tuning Features

AudioControl LCAudioControl has included their Patent Pending MILC circuit in the LC The Maximum Input Level Control circuit monitors both the input to the amp and the output of each pair of channels through a group of four LEDs. When the input signal has reach clipping, the Input LED will illuminate. When any pair of channels clips, the corresponding Gain Maximized LEDs will illuminate. If all is ideal, you want to operate just below the level where these LEDs will come on.

As replacing factory source units becomes more and more difficult, AudioControl will continue to offer cool solutions that allow specialist mobile electronics retailers to upgrade the remainder of a audio system. Adding a high-power amplifier like the AudioControl LC will result in a dramatic improvement in the performance of any audio system. The features that AudioControl has included in the amplifier simplify the installer&#;s task of making your system sound great and eliminate the need for additional interface hardware.

If you are in the market for an amplifier to upgrade your factory audio system, there aren’t any with as many amazing integration features and adjustments as the AudioControl LC AudioControl includes a stellar five-year warranty on the amp and can proudly say it is assembled in the USA. If OEM integration, excellent sound quality and a complete feature set are part of your amplifier purchasing criteria, then the LC amp should be at the top of your shopping list.

Filed Under: Car Audio, Integration, PRODUCTS, Sponsored PostTagged With: Amplifiers, AudioControl

Sours: https://www.bestcaraudio.com/audiocontrol-lcamplifier/

Lc audio control

AudioControl LC W x 6 Car Amplifier

Power galore Two keys to unlocking great sound in a car stereo system are serious power and extensive control - and this amp's got them both. For power, AudioControl's LC 6-channel amplifier puts out watts RMS per channel, so it'll drive even the most demanding aftermarket speakers with plenty of headroom to spare. And if you're into bass, you could bridge this amp to 3-channel mode to drive three subwoofers with watts RMS each, watts in total. Active controls for active systems This amp will work well with a 3-way system that uses a pair of tweeters, midrange speakers, and subs. Highly adjustable crossover networks let you set high-pass, low-pass, and bandpass filters so each driver gets only the frequencies it was designed to play. AudioControl's AccuBASS circuit ensures maximum bass performance, even if you're connected to a factory radio that normally turns down the lower frequencies as you turn the volume up Add kick to your factory stereo AudioControl designed the LC to work equally well with aftermarket and factory stereos. Eight active speaker-level inputs allow you to connect to almost any factory radio, with signal summing accommodating the separate bass, midrange, and treble signals found in some factory systems. Signal sensing circuitry turns the amp on, via the front speaker-level inputs, so you won't need to run a remote turn-on wire throughout your vehicle. Convenient features Onboard LEDs indicate optimized signal flow for inputs and outputs, plus give you a warning when a source is too loud and causing distortion. An optional wired remote can get assigned to each and every channel pair so you can control volume from the front seat. Important Note: Some factory radios and amplifiers will not work without sensing that its speakers are connected to their outputs.

Sours: https://www.amazon.com/AudioControl-LCchannel-Stereo-Amplifier/dp/B07F9H6ZGX
LC7i Active Line Out Converter Discussion and Review

.

You will also be interested:

.



1972 1973 1974 1975 1976